White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

White Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

AT-3 Small White Nylon Tie Mount - Qty. 500 The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

AT-3B Small Black Nylon Wire Tie Mount - Qty. 500 The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

White Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500 The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Black Nylon Wire Tie Mount The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Black Nylon Wire Tie Mount The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!