Side Mount Rowlock Sockets Plain or Chrome Plated Zinc Alloy Black Polymer Bearings For Use with Fig. 1227, 1262 or 1267 Rowlock Horns Screw Size #10

Edge Mount Rowlock Socket Plain Plated Zinc Alloy Black Polymer Bearings For Use with Fig. 1227, 1262 or 1267 Rowlock Horns Screw Size #10

Rowlock Socket - Bronze Specs: Length: 2-3/8" Width: 7/8" Depth: 1" Screw Size: #10

Bi-Color LED Horizontal Mount - Chrome Plated Zinc This Perko light is certified for use on power-driven vessels under 20 meters (65.6 feet) in both the USA and European markets. Features: Chrome-plated zinc alloy top with black polymer base High-tech, self-contained LED modules Same footprint as the 0627/0628 incandescent lights (wiring hole and mounting screw locations may vary) 2-mile (USCG 2nm) certified Specifications: Voltage: 12 Volt LED Wattage: 2.5 watts Amperage: 0.21 amps Dimensions (L x W x H): 3-3/8 in. x 2-1/2 in. x 1-1/2 in. Screw Size: #6 Finish: Chrome Meets Global Specs for: ABYC C-5, NMMA Type Accepted, EN/ISO 19009:2015, ABYC A-16 (2016), 1972 COLREGS, RCD 2013/53/EU, USCG 33 CFR - 2nm NMMA Type Accepted Number: 2619657

Fishing Rod Holder - 65° Angled Flush Mount - Chrome Plated Zinc Features: Chrome Plated Zinc Alloy Flange Angled Flush Mount (Approximately 65°) Anodized Aluminum Tube Soft Black Liner Flange Gasket with Integral Flip-Up Cap D01 & DPD - Integral Drain Bib or 5/8 Inch I.D. Flexible Hose Specs: Mount Type: Angled Drain Bib: No I.D. Tube: 1-5/8" O.D. Tube: 2" Length Under Flange: 8" Flange: 4-1/4" x 3-1/2"

RAM® Twist-Lock™ Composite Suction Cup Ratchet Mount with Socket Arm The RAP-B-104-224U-QU1, composite, ratchet/pivot, suction cup mount is a low profile, light weight and secure suction cup mount that is perfect for securing electronic devices in your mobile environment. Simply attach the suction cup base to the windshield of your vehicle for an easy and safe way to view your electronic device in your vehicle. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials ensure your electronic device is safe, secure, and within easy reach. RAM’s patented design also dampens shock and vibration helping to extend the life of your mobile device.  Features: Assembly Hardware Included Suction Size: 3.3" Diameter Ball/Socket Size: B Size (1") Weight Capacity: 2lbs Materials: High Strength Composite

USB A / USB C Square Surface Mount Power Socket This square surface-mount USB 3.0 & USB-C power socket charges two devices simultaneously. When split, the total 6A output is 3A per side.  Features: USB 3.0 features Quick Charging (QC) for supported devices gives enough power to charge phones, pads, and tablets quickly and efficiently USB-C features Power Delivery (PD) for faster and more flexible charging A protective dust cap covers ports when not in use Constructed of injection-molded nylon Easy installation requires drilling a 3/16-in. hole for the wire connection, securing it to the surface with two #6 screws (not included), and snapping the concealed fastener cover in place Blue LED illumination IP65 rating CE & RoHS compliant Specifications: Output DC: 5V/6A Input: 8-32VDC USB-C Watts: 60W@24V USB 3.0 Watts: 36W@12V Dimensions (inch): 1-15/16” – 1-15/16” Depth: 3/4 in. Volts: 8-32 Weight: 0.07

Stainless Steel Side Mount LED Navigation Lights - 2 NM - Port & Starboard  LED Side Mount Side Lights 400079 are approved for USCG 2 NM (Colreg 2 mile). Constructed of corrosion resistant stamped 304 stainless steel. One pair includes port and starboard lights. Surface mounts vertically with two #8 FH fasteners (not included). 12VDC. Low amp draw.  All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flush Mount Flagpole Socket - 25° - 1-1/4" ID - 316 Stainless Steel The 25° Flush Mount Flagpole Socket accepts flagpoles up to 1-1/4” in diameter. Maximum speed 10 MPH. Constructed of corrosion resistant investment cast 316 stainless steel. Installs with three #12 FH fasteners (not included).

Front Mount Power Socket This SAE-type polarized electrical connector is a two-prong power socket connector set. Great for solar panel connections and maintaining battery charge. Drill a 3/4” hole and install with two #10 RH screws (not included). Features: 14-gauge duplex wire Specifications: Length: 5 in. Volts: 12-24 Maximum Amps: 20A @ 12VDC Wire Guage: 14 AWM Weight: 0.12 lb.

Back Nut Mount Power Socket This SAE-type polarized electrical connector is a two-prong power socket connector set. Great for solar panel connections and maintaining battery charge. Installation is as easy as drilling a 7/8” hole, inserting the socket body, tightening the locking nut, and connecting the wires.  Features: 14-gauge duplex wire Specifications: Length: 5 in. Volts: 12-24 Maximum Amps: 20A @ 12VDC Wire Guage: 14 AWM Weight: 0.13 lb.

Bait Caster / Spinning Rod Holder Holds a bait caster reel in a cushioned cradle.A slot in the front of the rod holder allows for a spinning reel to be securely held in position. The rod holder design has a side mounted flange, which leaves the bottom open. This allows for the rod holder to accommodate trigger grips. Pistol grip rod butts easily clear the sides of the rod holder for quick rod retrieval. Rod can be secured in holder with a soft latching strap which snaps over the top. Includes No. 241 combination deck or side mount. WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

280 Bait Caster / Spinning Rod Holder Holds a bait caster reel in a cushioned cradle.A slot in the front of the rod holder allows for a spinning reel to be securely held in position. The rod holder design has a side mounted flange, which leaves the bottom open. This allows for the rod holder to accommodate trigger grips. Pistol grip rod butts easily clear the sides of the rod holder for quick rod retrieval. Rod can be secured in holder with a soft latching strap which snaps over the top. Includes No. 241 combination deck or side mount. WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Portable Side Mount with Dual Lock 4 Rod Holder The great side-mount Rod Holder in a portable version.  Easy to install using a 3M Dual-lock technology.  Simply clean and place the mounting squares where you want and you're done.  The VHB adhesive mounts to plastic, wood, masonry, metal or aluminum and is a permanent adhesion.  Indoor/Outdoor use - great for aluminum boats, docks, garages - anywhere you want to store your rods.  Rod Holders can be removed easily for cleaning, or with additional mounting squares can be used in multiple locations.  Holds up to 4 Rods.

Portable Side Mount with Dual Lock 6 Rod Holder The great side-mount Rod Holder in a portable version.  Easy to install using a 3M Dual-lock technology.  Simply clean and place the mounting squares where you want and you're done.  The VHB adhesive mounts to plastic, wood, masonry, metal or aluminum and is a permanent adhesion.  Indoor/Outdoor use - great for aluminum boats, docks, garages - anywhere you want to store your rods.  Rod Holders can be removed easily for cleaning, or with additional mounting squares can be used in multiple locations.  Holds up to 6 Rods.