Accumulator Tank The use of an accumulator tank is recommended to ensure effective and reliable system function. With an accumulator tank incorporated in the system, the intervals between cut-in and cut-out will be longer when only small amounts of water are drawn off. Less wear and tear on the pump with fewer starts and stops. Pre-pressurized at 0.8 bar / 12 psi. Volume: 2L/0.5gal Port connections: 1/2" hose Height: 315mm/12.4" Diameter; 160mm/6.3" Weight: 1.2kg /2.7lbs

Accumulator Tank The use of an accumulator tank is recommended to ensure effective and reliable system function. With an accumulator tank incorporated in the system, the intervals between cut-in and cut-out will be longer when only small amounts of water are drawn off. Less wear and tear on the pump with fewer starts and stops. Pre-pressurized at 0.8 bar / 12 psi. Volume: 2L/0.5gal Port connections: 3/4" hose Height: 315mm/12.4" Diameter; 160mm/6.3" Weight: 1.2kg /2.7lbs

Jabsco 18590-0010 Pump 12V Macerator 1" ID Hose Barb Pump Body: Plastic Self-Priming Flexible Impeller with Stainless Steel Wearplate. Port Size: Inlet – 3" Slip-on Hose Outlet: 1" ID Hose Barb Flow: 13 GPM at 5 feet of head Impeller: Nitrile Shaft Seal: Lip Type Shaft: Stainless Steel Motor: 12 Vdc Permanent Magnet Type, Fully Enclosed, with Stainless Steel Shaft. Macerator: Cast Bronze Cutter reduces particle size to 1/8" maximum.   The Jabsco 18590-series DC macerator pump unit is the ideal solution for emptying holding tanks on recreational vehicles and avoiding dump stations. The macerator section grinds waste down to a particle size of 1/8" maximum so it can easily be pumped through a 1" ID discharge hose. The pump section is self-priming, permitting the unit to be mounted above the tank in a convenient location. Empties most recirculating toilets in less than 2 minutes; empties a typical 30 gallon holding tank in less than 3 minutes.  

500 GPH Ultima Combo Automatic Submersible Bilge Pump 12V Johnson Pump Marine Ultima Combo bilge pumps are JPM's proven Cartridge Bilge Pumps combined with the non-clogging electronic switch Ultima Switch™ for automatic operation. The electronic automatic switch Ultima Switch™ uses the patented Mirus field effect detector cells producing micro-electrical fields that detect disruptions caused by level of water present in the bilge and automatically activates and deactivates the pump. CE-Approved Features: Pre-configured with an electronic Ultima Switch for automatic operation Capacities 500 GPH, 750 GPH, 1000 GPH and 1250 GPH Extremely energy efficient Water-cooled motor for long service intervals Compact, all-in-one motor/impeller unit with stainless steel (SS2343) shaft No tools needed for maintenance, no need for complete disassembly. You can now leave the pump casing attached to both the boat and the hoses.  500 GPH, 750 GPH, and 1000 GPH pumps have easy-to-install Dura-Port discharge ports to eliminate stress cracking caused by over-tightened hose clamps 500 GPH, 750 GPH, and 1000 GPH pumps are delivered including both a straight and a 90° smooth elbow Dura-Port as well as a removable check valve Meets the international standard, ISO 8849 marine Pump body: Thermoplastic Shaft seal: Lip seal Shaft: Stainless steel Voltage: 12v Wire size: 16GA Hose size: 3/4" Includes Dura-port connection Specifications Capacity 3ft (0.9 m) head (13.6V/27.2): 33 l/min - 525 GPH Capacity straight (13.6V/27.2V): 40 l/min - 630 GPH Amperage: 2.5 A Fuse size: 5 A Connection: 3/4" Length: 4.41" (112 mm) Width: 4.25" (108 mm) Height: 3.35" (85 mm) Weight: 14.4 oz.

1250 GPH Ultima Combo Automatic Submersible Bilge Pump 12V Johnson Pump Marine Ultima Combo bilge pumps are JPM's proven Cartridge Bilge Pumps combined with the non-clogging electronic switch Ultima Switch™ for automatic operation. The electronic automatic switch Ultima Switch™ uses the patented Mirus field effect detector cells producing micro-electrical fields that detect disruptions caused by level of water present in the bilge and automatically activates and deactivates the pump. CE-Approved Features: Pre-configured with an electronic Ultima Switch for automatic operation Capacities 500 GPH, 750 GPH, 1000 GPH and 1250 GPH Extremely energy efficient Water-cooled motor for long service intervals Compact, all-in-one motor/impeller unit with stainless steel (SS2343) shaft No tools needed for maintenance, no need for complete disassembly. You can now leave the pump casing attached to both the boat and the hoses.  500 GPH, 750 GPH, and 1000 GPH pumps have easy-to-install Dura-Port discharge ports to eliminate stress cracking caused by over-tightened hose clamps 500 GPH, 750 GPH, and 1000 GPH pumps are delivered including both a straight and a 90° smooth elbow Dura-Port as well as a removable check valve Meets the international standard, ISO 8849 marine Pump body: Thermoplastic Shaft seal: Lip seal Shaft: Stainless steel Voltage: 12v Wire size: 16GA Hose size: 1-1/8" Does not include Dura-port connection Specifications Capacity 3ft (0.9 m) head (13.6V/27.2): 60 l/min - 952 GPH Capacity straight (13.6V/27.2V): 73 l/min - 1150 GPH Amperage: 3 A Fuse size: 5 A Connection: 1-1/8"" Length: 4.41" (112 mm) Width: 4.25" (108 mm) Height: 3.35" (85 mm) Weight: 16 oz.

1.1 GPM WPS Pump - 12V FL2202 Features: Duty Cycle: Intermittent Smooth operation Self Priming and silent running Low power draw Runs dry without damage Easy connecting system 3/8" barb Do not use pump in a flammable environment

Automatic Submersible Bilge Pump - Ultima Switch 01674-001 Heavy-Duty, high-performance pump Exceeds the tough demands of commercial and recreational duty Liquid Cooled 12-Pole motor with double ball bearings Lip Seal design construction Prewired with automatic float switch(with Manual Over-ride Operation) Optional and removable check valve included 1-1/8" & 1-1/4" hose adapters included 3 year warranty

Viking Power 16 - 12V A modern, single-chamber, self-priming diaphragm pump that can be set up in several different pump/motor configurations. It is easy to install anywhere after the drain outlet in the wastewater system or as a bilge pump in any leisure craft - new or used. Its non-choke valves mean that no in-line filters are necessary. The pump can be run dry, and it can also handle a mixture of air and water without difficulty. The Viking Power 16 is self-priming up to a height of 3 meters. With its low pulse and muffled rubber bracket, this pump offers quiet operation. Specifically designed to pump waste water, the Viking Power 16 has been built to last, and engineered for easy maintenance. When it comes time to replace the premium grade reinforced nitrile rubber diaphragm, you can put in a spare without even removing the pump from the system. Delivered with 1" hose and 3/4" hose 1/2" BSP KlickTite™ XL connectors. 90° KlickTite™ XL connectors available as extra accessory. Capacity, Open Flow:16 l/min - 4.2 GPM Capacity at 0.1 bar: 15 l/min - 4.0 GPM Max Lift:3M - 9.8' Max Head:3M - 9.8' Connection: KlickTite™ XL connectors for 1" hose or 3/4" hose and 1/2" BSP threads; straight and 90°(optional)

Viking Power 16 - 24V A modern, single-chamber, self-priming diaphragm pump that can be set up in several different pump/motor configurations. It is easy to install anywhere after the drain outlet in the wastewater system or as a bilge pump in any leisure craft - new or used. Its non-choke valves mean that no in-line filters are necessary. The pump can be run dry, and it can also handle a mixture of air and water without difficulty. The Viking Power 16 is self-priming up to a height of 3 meters. With its low pulse and muffled rubber bracket, this pump offers quiet operation. Specifically designed to pump waste water, the Viking Power 16 has been built to last, and engineered for easy maintenance. When it comes time to replace the premium grade reinforced nitrile rubber diaphragm, you can put in a spare without even removing the pump from the system. Delivered with 1" hose and 3/4" hose 1/2" BSP KlickTite™ XL connectors. 90° KlickTite™ XL connectors available as extra accessory. Capacity, Open Flow:16 l/min - 4.2 GPM Capacity at 0.1 bar: 15 l/min - 4.0 GPM Max Lift:3M - 9.8' Max Head:3M - 9.8' Connection: KlickTite™ XL connectors for 1" hose or 3/4" hose and 1/2" BSP threads; straight and 90°(optional)

400 GPH 12V Bilge Pump - Barbed Port A small, price-wise alternative in the submersible bilge family. The low-cost choice for boat owners who do not want to forsake quality. Features: Capacity straight (13.6V/27V): 30 I/min. - 475 GPH Voltage: 12 V DC Amperage: 2.5A Fuse Size: 3 A Connection: 3/4" Max height: 100mm - 4" Weight 0.35kg - 12oz CE-Approved Barbed Port

JMP Marine JPR-VP0020D Volvo Penta Replacement Seawater Pump Replaces Volvo Penta 3583089, Johnson 10-13283, Ancor ST347, AN5893 Note: Pump Without Gear   Product Information & Specs: Uses JMP Impeller p/n: 7100-01K Pump Weight (approx): 4.25 LBS (1.93 KG) Replaces Genuine Volvo Penta Pump: 3583089 Replaces Johnson Pump: 10-13283 Replaces Ancor Pump: ST347, AN5893 Engine Model(s): D2 SERIES D2-55A/B/C/D/E/F, D2-75A/B/C/F   Parts Internally Compatible to Genuine: YES   Product Features: Plug & Play Replacement Heavy Duty Marine Grade Casting Marine Grade Shaft (3X Series Non-Magnetic) Lip Seal High Performance Flexible Impeller

CM30P7-1 - 12V - Circulation Pump - Dia16 Features: 12V, 5.3 GPM circulation pump Compact, magnetic driven centrifugal pump High flow rate with very low electrical current consumption Suitable for fresh water, ethylene glycol and salt water

CM30P7-1 - 12V - Circulation Pump - Dia20 Features: 12V, 6.9 GPM circulation pump Compact, magnetic driven centrifugal pump High flow rate with very low electrical current consumption Suitable for fresh water, ethylene glycol and salt water

MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 15 Part #: MP21381 Size: 3 in. NPT Flow-Rate: 320 GPM Head Feet: 145   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

CM10P7-1 - 12V Circulation Pump Features: 12V, 4.0 GPM circulation pump Compact, magnetic driven centrifugal pump High flow rate with very low electrical current consumption Suitable for fresh water, ethylene glycol and salt water