|
Commercial Duty Vane Pump - 12V
GROCO Vane Pumps are self-priming. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet), fuel transfer, ballast transfer, and oil change. Ignition protected motor and #316 stainless steel shaft. SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI.
Specifications:
Self Priming: YES
Thread NPT: 1/2" + Garden Hose Adaptor
Control Type: None
Max GPM: 7
Breaker DC: 15 Amp
|
892.00 |
|
|
Commercial Duty Vane Pump - 12V
GROCO Vane Pumps are self-priming. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet), fuel transfer, ballast transfer, and oil change. Ignition protected motor and #316 stainless steel shaft. SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI.
Specifications:
Self Priming: YES
Thread NPT: 1/2" + Garden Hose Adaptor
Control Type: None
Max GPM: 7
Breaker DC: 30 Amp
|
885.34 |
|
|
Groco C-60 24V Deck Wash Pump, 24Volt
Groco- Deck Wash Vane Pump System 6.5GPM 20-40psi 24VDC
More Info: C60
|
732.96 |
|
|
Commercial Duty Reversing Vane Pump - 24V
GROCO Vane Pumps are self-priming, are instantly reversible, and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet), fuel transfer, ballast transfer, and oil change. Ignition protected motor, #316 stainless steel shaft, and reversing (R). SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI.
Specifications:
Self Priming: YES
Thread NPT: 1/2" + Garden Hose Adaptor
Control Type: Pump Mounted Reversing Switch
Max GPM: 7
Breaker DC: 15 Amp
|
1146.67 |
|
|
Commercial Duty Reversing Vane Pump - 12V
GROCO Vane Pumps are self-priming, are instantly reversible, and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet), fuel transfer, ballast transfer, and oil change. Ignition protected motor, #316 stainless steel shaft, and reversing (R). SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI.
Specifications:
Self Priming: YES
Thread NPT: 1/2" + Garden Hose Adaptor
Control Type: Pump Mounted Reversing Switch
Max GPM: 7
Breaker DC: 30 Amp
|
1140.00 |
|
|
Heavy Duty Positive Displacement Vane Pump - 24V
GROCO Vane Pumps are self-priming and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet), fuel transfer, ballast transfer, and oil change. All models have an ignition protected motor and #316 stainless steel shaft.
Specifications:
Self Priming: YES
Thread NPT: 1/2" + Garden Hose Adaptor
Control Type: None
Max GPM: 6.5
Breaker DC: 15 Amp
|
415.33 |
|
|
Heavy Duty Positive Displacement Vane Pump - 12V
GROCO Vane Pumps are self-priming and are capable of operation in either direction. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet), fuel transfer, ballast transfer, and oil change. All models have an ignition protected motor and #316 stainless steel shaft.
Specifications:
Self Priming: YES
Thread NPT: 1/2" + Garden Hose Adaptor
Control Type: None
Max GPM: 6.5
Breaker DC: 30 Amp
|
408.67 |
|
|
Commercial Duty Water Puppy
Flow rate: 34 litres/min (9 USgallons/min)
Self-priming from dry up to 1.2m (4ft)
Features:
Small bilge debris present no problem to these bronze bodied, flexible impeller pumps.
Simple design means fewer wearing parts.
ISO 8846 MARINE (Ignition protection).
ISO 8849 MARINE (Bilge pump standard).
Motor
Permanent magnet type, fully enclosed, stainless steel shaft, ball type shaft bearing, has adequate torque to reverse the pump
Port Type
1/2" Internal Pipe Threads
1" External Hose Barb
Adapter for 3/4 " External Garden Hose Thread included
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
351.42 |
|
|
March 809 815 Series Mag-Drive Centrifugal Pumps
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze with Base 24VDC High Speed 7.5GPM 1/2"MPT Ports
|
498.00 |
|
|
Waste Water Diaphragm Pump - 32L(8.5GPM) - 24V
Single chamber, self priming, heavy duty diaphragm pump 24V for waste water. Black water transfer or pump out.
Capacity 32 L/min (8,5 GPM), flexible installation with 360 degree rotational ports. Quiet operation and low power consumption. Operates with no need for filter, equipped with double non-return valves.
Including 38mm (1,5″) straight and 90 degree rotational connectors. 3A fuse. Interchangeable with Johnson Pump 10-13373-04.
Specifications:
Weight: 1 kg/1.5Lb
Dimensions: 141/5.5L x 105/4H x 140/5.5W mm/in
Type: Black water
*Certification: CE marked 94/25/ECC, ISO8846 Small Craft, Electromagnetic compatibility 89/336/EEC, EN51014 1993/radio disturbance
|
152.87 |
|
|
Gianneschi PM40 24V 1" BARBS Diaphragm Pump 24V 40Lpm 1"
|
705.00 |
|
|
Gianneschi FS 40/14FE 24V Clutch Pump 24V
|
3772.98 |
|
|
Flojet 04300-505-24V Pump 24V 4.9/45 Pse Sw
This Flojet 04300-505-24v Diaphragm Pump runs on 24 Volts DC and has 5/8” Hose Barb Snap-In Ports. Open flow produces 4.9 gallons per minute with a 45psi switch. Made of Polypropylene, EPDM Valves and Santoprene Diaphragm.
|
269.35 |
|
|
Oberdorfer 406M Series Flexible Impeller Macerator
Pump Body: Bronze
Ports: Inlet: 1 1/2" Threads Outlet 1" NPT or 1 1/2 Hose
Flow: 25 GPM Max
Pressure: 44 PSI Max, 100 feet of head
Impeller: Neoprene Standard, Buna Optional
Shaft Seal: Mechanical Seal
Shaft: Stainless Steel
Motor / Drive: These Close coupled Rubber Impeller Pumps are mounted directly onto the electric motor without the use of a shaft coupling. This pump is coupled to standard motors with Nema C flange. It uses a motor adapter plate to accommodate the pump. We can supply additional motors and assemble for you.
CLOSE COUPLED RUBBER IMPELLER MACERATOR PUMP BRONZE
Portable. Compact. Easy Impeller Replacement. Macerator Easily Replaced. Reversible Wear Plate. Vacuum Switch Shut-off Pictured is Optional. Suction lifts of 15 ft. are possible when pump is fully primed.
Oberdorfer Flexible Impeller Macerator Pump, with 1HP, 24VDC, TEFC Motor, Painted White
This item is 'build to order'. Please contact us for lead time.
|
2146.25 |
|
|
Headhunter XRS-124 X-CAL 12/24V Pump
X-Caliber – 12-24V DC Water Pressure Pump
Quiet, reliable, blasting water pressure. Combining advanced DC motor and control technology with a proven self-priming centrifugal pump, the X-caliber surges past the competition with a flood of features.
A built in microprocessor interfaced with a rugged ceramic temperature and pressure sensor provides variable speed operation, prevents dry running damage and ensures complete electrical protection.
Part#Description
XRS-124X-Caliber 12-24 VDC Saltwater Pressure System
Control Panel:
Program power and pressure settings via the integrated control panel. Four colored LED’s display current settings and alarm conditions.
Advanced Features:
Adjustable cut in pressure
Adjustable power setting
Operates on 12 or 24VDC
Over voltage protection
Under voltage protection
Over current protection
Anti-flooding protection
Dry run protection
Variable Speed
Rotating bracket
Product Details/Specifications:
Liquid Temp
32°F (0°c)-104°F (40°c)
Ambient Temp
32°F (0°c)-122°F (50°c)
Max Pressure 67 PSI (4.5 bar)
Max Flow 10 GPM (38 lpm)
Suction/Discharge 3/4” FPT (Optional metric adapter)
Weight 16lbs (7.2 kg)
Dimensions 15”(382mm)L 8”(203mm)W 7”(178mm)H
|
2422.73 |
|