|
Gianneschi FS 40/14FE 24V Clutch Pump 24V
|
3772.98 |
|
|
Gianneschi FS 40/14FE 12V Clutch Pump
|
3772.98 |
|
|
Gianneschi ACB61E-24V Bronze 24V Self-Priming Pump
Gianneschi ACB61E-24V, ACB Series Self Priming Liquid Ring Pump and Motor unit, Bronze construction, Brass impeller, 316 Stainless Steel Shaft. Motor is 0.18KW (1/4 Horsepower), 3200 RPM, 24 Volts DC. Inlet Port is 1/2 Inch, Discharge Port is 1/2 Inch.
Applications for the ACB61E24V include fire fighting, oil and diesel, bilges, chain washing, and in pumping seawater as well as any fluids with high air content.
|
849.68 |
|
|
Gianneschi JET-4B-24V Bronze Jet Pump
Gianneschi JET-4B-24V, JET Series Jet Pump and Motor unit, Bronze construction, Brass impeller, 316 Stainless Steel Shaft. Motor is 0.75 KW (1 Horsepower), 2900 RPM, 24 Volts DC.
Applications for the JET4B24V include marine applications to pump fresh water and seawater, diesel oil liquids, non inflammables and liquids without any suspended parts. Most common uses are for sanitary systems, water supply for water pressure system, deck and chain washing, and fire fighting. This pump is selfpriming, it must only be used with clean liquids.
This is NOT suitable for pumping flammable fluids or for use in explosion hazard areas.
|
2881.11 |
|
|
Gianneschi 15CE1 Control-Press 24V 1" 1.5Bar
|
459.78 |
|
|
Gianneschi 15CE122 Control-Press 24V 1" 2.2Bar
|
459.78 |
|
|
Gianneschi C202-LG Blower 24V 01LC2031
Left rotation seen from the motor side - Complete with base
Power supply 24V - Power 0.07Kw - rpm 2800 - Flow rate 270m3 / h - Inlet diameter 100mm - Outlet diameter 78mm
|
484.83 |
|
|
Gianneschi 15CE3 Control-Press 24V 1.25
|
565.88 |
|
|
Gianneschi CP20-24V Bronze 24V Self-Priming Pump
Gianneschi CP20-24V, CP Series Self Priming Liquid Ring Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 0.18KW (0.25 Horsepower), 2800 RPM, 24 Volts DC. Inlet Port is 3/4 Inch, Discharge Port is 3/4 Inch.
Pump Body: Bronze
Impeller: Bronze
Shaft: 316 Stainless Steel
Port Size: Inlet Port is 3/4 Inch, Discharge Port is 3/4 Inch
Motor Specs : 0.18KW (0.25 Horsepower), 2800 RPM, 24 Volts DC
|
1095.94 |
|
|
Gianneschi ECOINOX-1-CE-24V Water System
|
1520.77 |
|
|
Gianneschi ECOINOX-2 CE 24V Water Pressure System
Ships Via Truck only ask us for a shipping quote at the Contact Us page. Please provide City,State and Zip Code.
|
1641.54 |
|
|
Gianneschi ECO-MV44-24V Bronze Screw Pump 24V
Gianneschi ECO-MV44-24V, MVG Series Single Screw Pump and Motor unit, Bronze construction, Buna Nitrile Stator, Stainless Steel Screw Rotor impeller, 316 Stainless Steel Shaft. Motor is 0.33 KW (0.4 Horsepower), 24 Volts DC. Inlet Port is 1 Inch BSP Inlet, Discharge Port is 1 Inch BSP Outlet.
Applications for the ECOMV4424V include emptying of Heavy Liquid Tanks Black And Grey Water, Emptying of waste, liquid with small suspended parts. This is a relatively simple pump that consists of a stainless steel rotor screw that turns through a rubber stator and pushes liquid along.
|
2375.87 |
|
|
Gianneschi PM40 24V 1" BARBS Diaphragm Pump 24V 40Lpm 1"
|
705.00 |
|
|
Gianneschi MAXI SUB 24V Submersible Pump 24V
Submersible Bilge Pump for seawater and grey water
Maxi Sub - 24volt
Voltage: 24 V
Power: 0,18 kW
Max flow: 180 L/min @ 2 m
Max head: 8m @ 30 L/min
Outlet: 1", female (vertical)
Stainless steel shaft (AISI 316) ; ABS open impeller
Diameter: 180 mm
Height: 290 mm
IP rating : IP68
|
888.68 |
|
|
Gianneschi CP20-12V Bronze 12V Self-Priming Pump
Gianneschi CP-20-12V, CP Series Self Priming Liquid Ring Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 0.2KW (0.25 Horsepower), 2600 RPM, 12 Volts DC. Inlet Port is 3/4 Inch, Discharge Port is 3/4 Inch.
Applications for the CP2012V include liquid intake, grey water discharges, bilges, showers, diesel and oil, galleys, as well as in pumping seawater and fresh water. This pump is not suitable for viscous liquids or pumping abrasive liquids. Install the pump in a dry and well ventilated location.
The pump must be placed on a solid surface in the horizontal position, feet down. To reduce vibration block the machine with the bolts to the surface and install some vibration dumpers. These pump usually do not need any maintenance so long as the following precautions are taken. If there is a risk of freezing, it is necessary to empty the pump casing then fill the pump up before running it again. Make sure the pump never runs dry.
|
1252.88 |
|