Pontoon Post Guide-On Loading your pontoon boat onto your trailer is much easier with post guide-ons. These guide-ons mount on top of rear cross member and fit in between the pontoons to center your boat on the trailer. Steel arms are made of 1-1/2" galvanized tubing and extend fully into sturdy 2" PVC tubes. Fit up to 3" x 4-1/4" frames. 22" high. Sold in pairs. WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

60" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features:  Mounting hardware and wiring included  Adjusts Out to 19" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" square, 16 gauge pre-galvanized steel uprights that are 39" high 2-3/8" diameter white PVC posts Stands 60" above the trailer frame Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27760: C.E. Smith 60" Post Guide-On With L.E.D. Posts Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

40" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 40" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware and wiring included  40" Total Height Adjusts Out to 13" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" sq. 16 ga Pre-Galvanized Steel post Extends 18" Into 2" PVC tube for strength Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27740: C.E. Smith 40" Post Guide-On With LED Lighted Posts   Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with I-Beam Mounting Kit & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With I-Beam Mounting Kits and two Camo Wet Lands Post Guide-On Pads. These Post Guide-Ons allow you to see the location of your trailer when it's underwater. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Brackets will fit onto any height and virtually any width I-beam trailer frame. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware included Adjusts out to 19" on each side 1-1/2" square. 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post-guide-on covers: Camo Wet Lands Kit Includes: Part 27648: C.E. Smith 60" Post Guide-On With I-Beam Mounting Kit  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with Unlighted Posts & FREE Camo Wet Lands Post Guide-On Pads This kit includes two 60" Post Guide-On With Unlighted Posts and two Camo Wet Lands Post Guide-On Pads. These Post Guide-Ons allow you to see the location of your trailer when it's underwater. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware included Adjusts out to 19" on each side Fits frames up to 3" W x 4-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 39" high 2-3/8" diameter white PVC posts. Stands 60" above the trailer frame with white post caps. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27640: C.E. Smith 60" Post Guide-On With Unlighted Posts  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  *Sold in pairs

PVC 40" Post Guide-On with Unlighted Posts & FREE Camo Wet Lands Post Guide-On Pads This kit includes two PVC 40" Post Guide-Ons With Unlighted Posts and two Camo Wet Lands Post Guide-On Pads. The PVC posts allow you to see the location of your trailer when it's underwater. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter). Features: Mounting hardware included Adjusts out to 13" on each Side Fits Frames up to 3" W x 4-1/4" H 18" high 2" schedule 40 white PVC posts (2-3/8" actual OD) Stands 40" above the trailer frame with white post caps Fits trailer frames up to 3" wide x 5-1/4" tall Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27620: C.E. Smith 40" Post Guide-On With Unlighted Posts Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

Angled Post Guide-On - 40" - Black with FREE Camo Wet Lands 36" Guide-On Cover Angled Post Guide-On - 40" - Black Providing an easy visual while centering your boat. The angled PVC Post Guide-Ons allow you to easily center your boat on your trailer at the ramp. Features: Fits trailer frames 3-1/4” wide by 4” tall Mounts above or below the trailer frame Adjusts up to 13” away from the trailer frame Angled to allow for wide or flared hulls 40” Tall For larger frames use P/N 11416 mounting U-bolts Post-Guide-On Pad - 36" - Camo Wet Lands The Post Guide-On Covers protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter). Covers are made from strong polyurethane-coated 600D nylon fabric with nylon closures on each end. Open the bottom and top to allow for an LED guide on lamps. 1/2" thick closed-cell polyurethane foam inner pad. Features: Length: 36" Color: Camo Wet Lands Sold in Pairs

Angled Post Guide-On - 40" - White with FREE Camo Wet Lands 36" Guide-On Cover Angled Post Guide-On - 40" - White Providing an easy visual while centering your boat. The angled PVC Post Guide-Ons allow you to easily center your boat on your trailer at the ramp. Features: Fits trailer frames 3-1/4” wide by 4” tall Mounts above or below the trailer frame Adjusts up to 13” away from the trailer frame Angled to allow for wide or flared hulls 40” Tall For larger frames use P/N 11416 mounting U-bolts Post-Guide-On Pad - 36" - Camo Wet Lands The Post Guide-On Covers protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter). Covers are made from strong polyurethane-coated 600D nylon fabric with nylon closures on each end. Open the bottom and top to allow for an LED guide on lamps. 1/2" thick closed-cell polyurethane foam inner pad. Features: Length: 36" Color: Camo Wet Lands Sold in Pairs

40" Post Guide-On With LED Lighted Posts  Post Guide-Ons allow you to see the location of your trailer when it's underwater. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear.  Features: Mounting hardware and wiring included  40" Total Height Adjusts Out to 13" each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" sq. 16 ga Pre-Galvanized Steel post Extends 18" Into 2" PVC tube for strength Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side). Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

40" Post Guide-On With Unlighted Posts These Post Guide-Ons allow you to see the location of your trailer when it's under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. Features: Mounting hardware included Adjusts out to 13" each Side Fits Frames up to 3" W x 4-1/4" H 18" high 2" schedule 40 white PVC posts (2-3/8" actual OD) Stands 40" above the trailer frame with white post caps Made in the USA Fits trailer frames up to 3" wide x 5-1/4" tall Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

60" Post Guide-On With L.E.D. Posts These Post Guide-Ons allow you to see the location of your trailer when it's under water. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear.  Features: Mounting hardware and wiring included  Adjusts Out to 19" each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" square, 16 gauge pre-galvanized steel uprights that are 39" high 2-3/8" diameter white PVC posts Stands 60" above the trailer frame Made in the USA Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) *Sold in pairs

60" Post Guide-On With Unlighted Posts  These Post Guide-Ons allow you to see the location of your trailer when it's under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. Features: Mounting hardware included Sold in pairs Adjusts out to 19" each side Fits frames up to 3" W x 4-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 39" high 2-3/8" diameter white PVC posts. Stands 60" above the trailer frame with white post caps. Made in the USA Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

75" Post Guide-On w/Unlighted Posts f/U-Bolt Mounting Product Description These Post Guide-Ons allow you to see the location of your trailer when it's under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. Features: Mounting hardware included Sold in pairs Adjusts out to 19" each side Fits frames up to 3" W x 5-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

60" Post Guide-On With I-Beam Mounting Kit Product Description These Post Guide-Ons allow you to see the location of your trailer when it's under water. Designed for I-beam trailers and I-beam boat lifts, these guide-ons feature an innovative two-piece mounting clamp that works above or below the I-beam. Brackets will fit onto any height and virtually any width I-beam trailer frame. Features: Mounting hardware included Adjusts out to 19" each side 1-1/2" square. 16 gauge pre-galvanized steel uprights 2-3/8" diameter white PVC posts Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) *Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Angled Post Guide On - 40" - White Providing an easy visual while centering your boat. The angled PVC Post Guide-Ons allow you to easily center your boat on your trailer at the ramp. Features: Fits trailer frames 3-1/4” wide by 4” tall Mounts above or below the trailer frame Adjusts up to 13” away from the trailer frame Angled to allow for wide or flared hulls 40” Tall For larger frames use with P/N 11416 mounting U-bolts