|
Large 800W XXXHEAT Boat Bilge & RV Heater
This Xtreme boat bilge and RV heater is suitable for boats up to 35' in length and medium RV compartments.
Features:
True forced air heating circulates air more effectively and heats it more evenly for more accurate climate control
The automatic thermostat turns the heater on at 40°F and off at 55°F +/-3° - the tightest tolerance available
Failsafe Design cannot overheat (heating technology is dynamic and self-regulating)
High Efficiency Xtreme produces heat faster, circulates more air, and shuts off earlier
A pre-wired 15 ft. marine-rated power cord with a 110V 3 prong plug eases installation
Designed for durability and reliability
Complete protection (fully anodized inside and out)
Small footprint
Certified and independently tested now with the UL 1278 standard
Specifications:
Wattage: 800W
BTU: 2729.7
Inrush (startup) Current: 14A, 1 sec.
Typical Operating Current: 6.5A
Fan Flow: 40 CFM
Heater Dimensions (inch): 8″ x 3.5″ x 5-1/8″
Fuse Size Required: 20A
Power Cord: 15 ft. marine-rated power cord
|
421.43 |
|
|
Small 400W XHEAT Boat Bilge & RV Heater
This Xtreme boat bilge and RV heater is suitable for boats up to 24' in length and small RV compartments.
Features:
True forced air heating circulates air more effectively and heats it more evenly for more accurate climate control
The automatic thermostat turns the heater on at 40°F and off at 55°F +/-3° - the tightest tolerance available
Failsafe Design cannot overheat (heating technology is dynamic and self-regulating)
High Efficiency Xtreme produces heat faster, circulates more air, and shuts off earlier
A pre-wired 15 ft. marine-rated power cord with a 110V 3 prong plug eases installation
Designed for durability and reliability
Complete protection (fully anodized inside and out)
Small footprint
Certified and independently tested now with the UL 1278 standard
Specifications:
Wattage: 400W
BTU: 1365
Inrush (startup) Current: 8.2 A, 1 sec.
Typical Operating Current: 4. A
Fan Flow: 40CFM
Heater Dimensions (inch): 5.75″ x 3.5″ x 5-1/8″
Fuse Size Required: 15A
Power Cord: 15 ft. marine-rated power cord
|
328.57 |
|
|
Medium 600W XXHEAT Boat Bilge & RV Heater
This Xtreme boat bilge and RV heater suit boats up to 28' in length and medium RV compartments.
Features:
Accurate forced air heating circulates air more effectively and heats it more evenly for more accurate climate control
The automatic thermostat turns the heater on at 40°F and off at 55°F +/-3° - the tightest tolerance available
Failsafe Design cannot overheat (heating technology is dynamic and automated)
High Efficiency Xtreme produces heat faster, circulates more air, and shuts off earlier
A pre-wired 15 ft. marine-rated power cord with a 110V 3 prong plug eases installation
Designed for durability and reliability
Complete protection (fully anodized inside and out)
Small footprint
Certified and independently tested now with the UL 1278 standard
Specifications:
Wattage: 600W
BTU: 2047.3
Inrush (startup) Current: 12A 1 sec.
Typical Operating Current: 5.5 A
Fan Flow: 40 CFM
Heater Dimensions (inch): 8″ x 3.5″ x 5-1/8″
Fuse Size Required: 15A
Power Cord: 15 ft. marine-rated power cord
|
375.06 |
|
|
Boat, Cabin, & RV Heater
This Xtreme boat and cabin heater is designed to help keep your boat cabin, RV, or other small space comfortable during the fall and winter months.
This heater features quiet operation, a low profile, and a stable base that prevents tipping. Drawing air from the top, this heater can be placed up against walls or on carpeted surfaces without blocking the air intake. The 1500-watt heat setting will quickly warm your living space, while the 750-watt setting will efficiently maintain comfortable temperatures. The 6 ft. power cord offers more flexibility for heater placement independent of outlet locations.
Features:
Built-in overheat protection
"One Shot" secondary overheat protection
Two heat settings: 750/1500 and 1500 watts
Freeze prevention thermostat setting
Fan-only setting
Automatic thermostat
6 ft. power cord
UL Listed to UL 1278 standards
Specifications:
Color: White/black
Wattage: Low: 750 / High: 1500
Amps: Low: 6.25 / High: 12.5
Voltage: 120V
Dimensions (inch): 10″ L x 10-1/4" W x 4-3/4" H
Cord Length: 6 ft.
Weight: 5lbs
|
126.06 |
|
|
Newbury, Massachusetts, April 15th, 2010: Technology changes rapidly and as a company building WiFi equipment, Island Consulting strives to offer the best. Since the beginning, Island Consulting has continuously made improvements to The Wirie, a long range WiFi solution for boats and RVs. The most recent development in creating a better product involves a high-end marine grade WiFi antenna. To achieve this goal, Island Consulting partnered with the well-known US antenna manufacturer, L-com.
L-com, a leading antenna manufacturer in the wireless connectivity business for over 27 years, agreed to produce a marine grade antenna exclusively for The Wirie. Designed to stringent specifications, the new Wirie antenna is an 8dBi omni-directional high performance marine antenna that features sealed collinear brass elements inside a durable UV-stable white fiberglass radome. The sealed end cap ensures no water entry and drain holes in the base help prevent moisture build-up inside the antenna.
The collaboration between Island Consulting and L-com offers the consumer an economical alternative to other true marine grade WiFi devices currently on the market. “We believe our partnership with L-com has allowed us to turn The Wirie into the most durable and best long range WiFi solution available for boats and RVs”, states Mark Kilty from Island Consulting. According to Karl Blomgren, L-Com's Product Manager, “L-Com is always interested in working with customers, like Island Consulting, to optimize our antennas for their applications to support new product enhancements.” Additional information about The Wirie's new antenna can be viewed at www.thewirie.com/antennadetails.html.
For $250, The Wirie enhances the customers' ability to connect to the internet from the comfort of his/her own boat or RV. The Wirie continues to offer many unique features: flexible stainless steel mounting bracket, easy to install and use software, comprehensive user manual, powerful 1000mW WiFi adapter, IP67 waterproof box, and superior customer support. The Wirie is easy to upgrade as technology continues to advance. In addition to the new antenna, the warranty of The Wirie has been extended to 1 year. The 10-day money back guarantee is still in place.
Through the joint effort between Island Consulting and L-com, The Wirie is a truly marine grade WiFi solution at an affordable price.
For more information, please visit www.thewirie.com.
About The Wirie:
Island Consulting located in Newbury, Massachusetts, USA, manufactures and distributes The Wirie. The Wirie was invented in the Caribbean in April 2009 to provide a cost-effective, user-friendly, long range WiFi solution for boats and RVs. It was quickly expanded to a U.S. operation to allow a larger distribution. Island Consulting is committed to continuous improvements and to making sure every customer is extremely satisfied. Website: www.thewirie.com
About L-com:
Founded in 1982, L-com Global Connectivity is a privately held corporation in Massachusetts, USA, dedicated to the design and production of a wide range of interconnect products for the electronics and data communication industries. L-com places primary product emphasis on copper and fiber cable assemblies, wireless antennas and amplifiers and accessories for modular, coaxial and computer networking applications. In June 2007, L-com acquired HyperLink Technologies of Boca Raton, Florida, USA. Website: www.L-com.com
Contact:
Liesbet Collaert
liesbet@thewirie.com
http://www.thewirie.com
The Wirie can now be found at CLR Marine.
http://www.clrmarine.com/462.html?m4:cat=%2FCOMMUNICATION
http://www.clrmarine.com/462.html?m4:cat=%2FCOMMUNICATION%2FAntennas
http://www.clrmarine.com/462.html?m4:cat=%2FCOMMUNICATION%2FMobile%20Broadband
http://www.clrmarine.com/m4_view_item.html?m4:item=0Wirie
|
|
|
800W Heating Element for Sigmar Heater- 110V
Made of Incoloy
11" Long
1-5/8" Diameter British threads
7-3/4" Long standard electrical anode rod
|
115.00 |
|
|
Large Swingback Back Boat Seat Cover - Vinyl White
Keep your seats and consoles from cracking and fading! Boat seat and console
covers are designed to protect your seats from damaging ultra-violet rays,
wind, mildew and water. All Covers fold easily for storage and keep your
seats cool and clean!
Dimensions: 36"H x 40"W x 20"D
Features:
Mildew and water repellant
UV Protection
Waterproof
Air vents
Heavy duty
Drawstring hem
|
34.54 |
|
|
As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away.
Outside Storage?
It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.
Rinse/Flush
Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat.
Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring.
Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present.
Salt
Watch out for salt. Buy a good salt remover to minimize corrosion.
Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine.
Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4*
STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel.
Batteries
Remove the batteries from your boat and store in your garage or basement.
Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery.
If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat.
Cleaning
Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint.
Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins.
Cover Up
If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often.
https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html
and
https://www.clrmarine.com/462m4/winterizing.html
Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information.
Fair winds and smooth sailing.
To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/.
_________________________________________________________________________
Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten.
She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com
©Copyright Cheryl Kuba, 3happycampers.com, 2021.
|
|
|
Quick Release Bracket for 450W & 600W Heaters
Install and Remove your Xtreme Heater FAST!
Driven by customer demand, our quick-release bracket was designed specifically for your Xtreme heater and allows you to easily install and remove your heater(s) in seconds, without the need for tools.
Using this bracket, your mounting options include locations you may not have considered due to concern for blocked access to other components in your tight engine space.
For our customers who prefer to leave their heater(s) in place only during the winter months, THIS is the accessory you've been asking for. The quick-release bracket makes it simple to remove the heater for the boating season, leaving just the low-profile bracket installed and ready to go. When winter returns, lock it down, and plug it in!
Features:
Built Xtreme Tough, anodized aluminum construction will not corrode
Provides easy off-season storage, for quick access to engine spaces
Works on ALL Xtreme Heaters built after 2004
Quickly Install and Remove your Heater Without Tools!
One Year Warranty
|
47.68 |
|
|
Premium Water Heater 5.8G - 120V
Marine Premium Water Heater 22L (5,8 gal) 800W 120V, toxic free ceramic inside coating to ensure highest water quality over time
Features:
Heats up 22L (5,8 gal) in 1h, good for 35L of mixed warm water or a 3,5 minute shower
Replaces common brands as Isotemp
Toxic Free Ceramic Double coating
Specifications:
Weight: 10,5 kg/24 Lb
Dimensions: 423/16.65L x 390/15.35H x 390/15.35W mm/in
*CE marked (LVD) directive 2006/95/EC, EN 60335-1 (2008), EN 60335-2-21 (02-2004), A1 (07-2005), EC (01-2008). (EMC) directive: 2004/108/EC, EN 55014-1 (1999), A1 (2000), A2 (2003), EN 55014-2 (1998), A1 (2002)
|
481.84 |
|
|
True North Deluxe 9206 120VAC High-Performance Space Heater - 600W, 900W & 1500W
600, 900, and 1500 watt electric space heater. Rugged, steel body construction. Dual overheat protection.
This rugged AC electric heater keeps the cabin warm on the chilliest of those early and late season nights in the marina. The model 9206 True North AC heater was recognized by Powerboat Reports as being the best. There is no other heater on the market that delivers the performance and quality of the True North.
Features:
Steel construction
3 heat settings (600, 900, and 1500 Watt)
Option of a 'fan only' setting
Built-in thermostat
Anti-freeze setting
Low profile design
Made in Canada
5-year warranty
Benefits:
Years of trouble-free use
Extended boating season
Greater on-board comfort
Can use for 'no heat' air circulation
Eliminate snow or frost build up on boat top
Cannot tip over
Easy to stow when not in use
|
97.44 |
|
|
Clamp-On Rail Mounted Cup Holder - Large for Up to 2" Rail - Grey
Camco's Clamp-On Rail Mounted Cup Holder provides a secure location to keep your beverage. It is a great addition to any boat with 1-1/2-inch to 2-inch rails. The secure clamp assembly keeps the cup holder in place with the help of tension adjustment screws. Swivel mount allows you to install on any angle rail keeping your cup holder level and in place. The cup holder is constructed of a durable, UV-resistant polymer and fits most standard sized drinks, cups, cans, bottles and tumblers.
Features:
The Perfect Boating or RV Accessory: Provides a secure location to keep your beverage; Cup holder mounts to 1-1/2-inch to 2-inch boat rails
Compatibility: Fits most standard cups, cans, bottles and tumblers
Swivels to Any Angle: Swivel mount allows you to install on any angle rail keeping your cup holder level and in place
Durable Construction: Constructed of a durable, UV-resistant polymer
Color: Grey
|
10.62 |
|
|
Clamp-On Rail Mounted Cup Holder - Large for Up to 2" Rail - White
Camco's Clamp-On Rail Mounted Cup Holder provides a secure location to keep your beverage. It is a great addition to any boat with 1-1/2-inch to 2-inch rails. The secure clamp assembly keeps the cup holder in place with the help of tension adjustment screws. Swivel mount allows you to install on any angle rail keeping your cup holder level and in place. The cup holder is constructed of a durable, UV-resistant polymer and fits most standard sized drinks, cups, cans, bottles and tumblers.
Features:
The Perfect Boating or RV Accessory: Provides a secure location to keep your beverage; Cup holder mounts to 1-1/2-inch to 2-inch boat rails
Compatibility: Fits most standard cups, cans, bottles and tumblers
Swivels to Any Angle: Swivel mount allows you to install on any angle rail keeping your cup holder level and in place
Durable Construction: Constructed of a durable, UV-resistant polymer
Color: White
|
10.62 |
|
|
FINISH THOMPSON A100855 STRAINER POLYPRO
Inlet Strainer - Prevents intake of objects or particulates.
Part Number
Construction
Applicable Model
A100855
Polypropylene
PFP
A100111
316 Stainless Steel
PF, BT
A100337
316 Stainless Steel
TTS, TBS
A100109
PVC/Polyethylene
TTC
|
44.28 |
|
|
RealVision 3D™ All-In-One Bronze Thru-Hull Transducer - 0° - 8M Cable
Raymarine’s RV-200 Bronze All-In-One Through Hull Transducer is designed for inboard and outboard powerboats. The RV-200 lets you easily identify structures and locate fish with the life-like clarity of RealVision 3D™ sonar.
The RV-200 is a 4-channel, Wide Spectrum CHIRP transducer with DownVision™, SideVision™, high frequency CHIRP fish targeting and RealVision 3D™ sonar inside. The transducer has a built-in attitude and heading reference system (AHRS) that stabilizes the sonar imagery, automatically compensating for vessel motion. You’ll enjoy crystal-clear imagery in waves, swells, and while maneuvering. The RV-200 also has a built-in fast response water temperature sensor for quick, accurate readings.
The RV-200 features a rugged cast-bronze through hull body suitable for fiberglass or wooden hulls. The RealVision 3D™ transducer elements are arranged with a 0° offset for boats with flat bottoms. The lowprofile design slips effortlessly through the water without causing drag or cavitation. The near-flush RV- 200 works great on trailered boats too, and with no fairing block to cut, installation is a breeze.
What’s in the Box?
RV-200 Bronze All-In-One Through Hull Transducer with 8-meter (26-foot cable)
Anti-rotation bolt kit
Installation instructions
|
1319.99 |
|