BERKELEY S15094, SET OF PACKING RINGS

Micropump GJ-N25.PF1S.B Pump Head B Mount Micropump 81809 GJ Series Pumphead with Port/fittings 1/8-27 (F) NPT Side Ports, Max Speed 5500 RPM, Max Pressure 300 psi and Max Temp 77 (C). Micropump GJ-N25.PF1S.B Mag-Drive Gear Pump Head, Requires A-Mount compatible Drive. 81809 constructed of Base Material 316SS, Gear Material PPS (carbon fiber/ptfe) and Shaft Material 316SS. Pump Series: GJ Series Ports/Fittings: 1/8-27 (F) NPT Side Ports Min Speed (RPM): 500 Max Speed (RPM): 5500 Max Pressure (psi): 300 Min Temperature (°C): -46 Max Temperature (°C): 77 Max Diff. Pressure (psi): 69.6774193548387 Displacement (ml/rev): 0.91 Design: Standard Design Gear Set: 0.500/2/24 (0.91ml/rev) Gear Material: PPS (carbon fiber/ptfe) Static Seals: PTFE Gasket (.004) 5369 Base Materials: 316SS Drive Mount: MP Plate Bypass: No Driven: Ferrite Driving Magnet: Not Included High System Pressure: No Bushings: PPS (carbon fiber/ptfe) Shafts: 316SS Gear Trim: None Part Number: 81809 Model: GJ-N25.PF1S.B

Ampco Pumps P1SX015098006 17-4 Sleeve

Gianneschi CB25/16B-B 230V 50Hz Mpu Gianneschi CB-25/16-B-B-230V, CB Series Centrifugal Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 1.1 KW (1.5 Horsepower), 2900 RPM, 230 volts AC, Single Phase. Inlet Port is 1-1/2 Inch BSP Inlet, Discharge Port is 1 Inch BSP Outlet.   Applications for the CB25/16BB230V include air conditioning systems, water supply, lifting fresh or salty water at sanitary plants, water circulations, increasing water pressure at water plants, pumping fresh water and seawater, and cooling and heating.

Flexible Shaft Coupling for 5" B/W, Hurth, & Volvo - 25HP/100RPM Capacity The R & D Marine Flexible Coupling consists of a flexible disc molded with a polyester elastomer. The disc gives clearance for bolt heads and is able to flex freely to take up any temporary misalignment of the engine and shaft due to flexing of the boat structure or the engine moving on its mount. Forward thrust is taken in compression on the disc between the two half couplings, and reverse thrust is retaken in compression on the disc between the two fail-safe straps. In the unlikely event of a severe impact, the steel straps make the coupling fail-safe and ensure the drive is maintained both forward and reverse. Reduce Engine Noise & Transmission Vibration Staggered bolts enable the element to isolate vibrations and compensate for some misalignment. Reduces Costly Transmission Repairs Absorbs shock loads due to hard gear changes. Fits Most Major Transmissions For engines, 5 to 1,500 horsepower It fits brands such as Borg Warner, ZF-Hurth, Twin Disc, Volvo, Yanmar, Technodrive, and more. Under Compression Load In Both Forward & Reverse The aft steel strap bolted to the transmission acts as a backing plate to prevent reverse thrust from pulling the element apart. Quick & Easy Installation The R & D Marine Flexible Coupling requires no machining and comes supplied with bolts to connect between the two existing shaft flanges. Extremely Durable Impervious to saltwater, diesel, and lubrication oils. The Flexible Couplings are made from a polyester elastomer not affected by saltwater, diesel, or lubrication fluids. Fail-Safe Design A fail-safe design is incorporated in the R & D Flexible Shaft Coupling that prevents the two couplings from pulling apart in the event of an impact or element failure, whereas other couplings do not. This fail-safe design is accomplished by using two steel straps and thru-bolts going into both the shaft coupling and transmission output flange. The aft steel strap is bolted to the transmission output flange, and the front strap is bolted to the shaft coupling. In the event of an impact, the aft steel strap (bolted to the transmission) will catch the front steel strap (bolted to the shaft coupling) and prevent the drivetrain from pulling apart. The R & D element will absorb the shock load (reducing or eliminating damage to the transmission) and will maintain contact between the two couplings. The steel straps also keep the R & D Flex-Coupling under a compression load in both forward and reverse operation (the aft strap bolted to the transmission acts as a backing plate). Machined Not Molded The Drivesaver is molded, while the R & D Flexible Shaft Coupling is machined. Both designs suggested that you first set your alignment by drawing the two couplings up to each other and then adding the flex-coupling. The machined part will have MUCH tighter tolerance than a molded part. Checking Alignment The R & D Flexible Shaft Coupling allows for alignment inspection after the element is bolted in place. There is one bolt head that is machined and painted red. After the R & D Flexible Shaft Coupling is bolted into place, a feeler gauge can be slipped between the red bolt head and the coupling. This process is repeated with the same bolt four times at 90-degree intervals by rotating the shaft. If the gap is within .010" (0.25mm), the engine is accurately aligned. To calculate the power of the coupling required: Horse Power of Engine x Reduction Ratio x 100 = HP/100RPM       Engine Speed   Example: Ford 150 HP at 2500 RPM with Borg Warner Velvet Drive 72C 2:1 Reduction Ratio Engine Horse Power is 150 HP, Max Rated RPM is 2500, Reduction Ratio is 2:1 150/2500 x 2 x 100 = 12 HP per 100RPM The coupling required is 910-009 Specifications: Manufacturer: B/W, Hurth, Volvo Diameter (inches/mm): 5 / 127 # of Bolts: 4 Diameter of Holes (inches/mm): 0.44 / 11.2 Bolt Pitch Circle (inches/mm): 4.25 / 107.9 Register (inches/mm): 2.5 / 63.5 Diameter (inches/mm): 5.63 / 143 Length (inches/mm): 2.06 / 52.4 Bolt Diameter: 7/16 UNF HP per 100 RPM (hp / kW): 25 / 18.64

Groco B-200 Motor Base Stamping, Blk  

Groco B-200-G Pump Base Grommets (4Pk)  

Groco S-73-B Tie Rod, 316Ss .250 X 8.938  

Groco S-87-B Tie Rod .250 X 12.813  

Groco S-82-B Tie Rod Nbr .313 X 9  

Groco Arg-501-B Casting, Cap Less Label  

Groco Arg-1001-B Cover Casting And Label  

Groco Arg-1501-B Cover Casting And Label  

Groco P-9022-B Mount Feet Set Of 4  

Groco S-88-B Sight Glass